Coil cleaning should be done as part of a routine maintenance visit by a Trane Comfort Specialist. Before your specialist arrives take care to remove any flowers, bushes, weed or grass that has potential to get inside the unit and remember foliage should be at least 2 feet away from the unit. You can expect your specialist to perform the following steps for Disconnect power to the air conditioner: A Trane Comfort Specialist will look for the shutoff box outside near the unit. there is not shutoff box, you will need to show the specialist where the circuit breaker is located to turn the power off there. Remove outer case: Depending how the outer case of access panels are attached, your specialist will need either a screw or nut driver to do this. Remove top of air conditioner: Some air conditioners are constructed with the fan assembly attached to the top. conditioner is constructed this way, your specialist will be careful

not to stretch or damage any wires. Clean and lubricate assembly: Your specialist will clean any dirt off the fan blades and use a shop vacuum to clean dirt off the fan motor and shaft. If the motor requires any lubrication, a small amount will be applied to each of its lubrication ports. Clean A/C coils: Dirt will be whisked away from the surface of the coils with a broom. Spray trapped dirt away from coils: After covering any exposed wires or motors with plastic, your specialist using either water or a biodegradable foaming cleaner will spray cleaner soak for 10 to 15 minutes on the coils. Remove cleaner: Spraying rinse water from the inside, your specialist will remove the cleaner and any dirt away from the air Inspect coil fins for damage: Using a special comb, your specialist can straighten any bent coil fins. Reassemble the air conditioner: Your specialist will reassemble your air conditioner now that your coils are clean.

Please agree to the updated terms and conditions Manufacturers using NBS National BIM Library adhere to our code of conduct. Click on model # for Specifications and Dimensions for specific model Air Cooled Single Duct AC Units - Standard Features For both air cooled or water cooled applications. Units designed for mounting above 2 ft. x 4 ft. suspended panel opening. Provides comfort and temperature control for many types of areas. Copper tube, aluminum fin, mounted in a stainless steel drain pan. Protected by thermal overload protection with both high (manual reset) and low (automatic reset) pressure switches. An expansion valve, a liquid line filter/dryer, and a sight moisture indicator provide a completely self-contained factory precharged refrigeration circuit. Attractive 3-Way Supply Air Diffuser And Return Air Grille Shipped loose for "No Duct" units. Single duct units only require a return air grille and double units require neither. 3 Speed, long life motors for single phase operation.

Quick Clip Mounting Isolators Mean fast and easy installation. why does window ac unit leak waterIsolation is always an important factor for noise.horizontal ac window unit Stainless steel and elevated to allow for proper trapping of condensate. how to tell how many tons your ac unit isDrain connections (3/4" f.p.t.) are provided on each side of cabinet. Provided for each drain pan to prevent overflow in the event of a blocked drain line or if unit is not installed in a level position. Switch is wired to unit control panel. Electrical Components to include: contactor (for AC or WC units only), relay(s), control transformer and power supply connections. Forward curved, direct drive for both supply fan and condenser fan (air cooled units only).

Standard on water cooled units. Rated at 150 PSIG. Remote thermostat, wall mounted (can be combined with 3 speed switch). Low ambient control on air cooled units Humidifier - evaporative media type includes humidistat-remote wall-mounted. Electric reheat (Hot water or steam on request) with factory-wired contactor and remote dehumidistat. Remote condensate pump package Transformer to 1-60-277 Volt. Remote status panel w/L.E.D. indicators for cooling, humidifying, condensate overflow. Flow control with a 2-way solenoid valve or a 3-way solenoid valve.The coil is the indoor component of your heating and cooling system, enclosed in the furnace or air handler. It’s where heat is transferred into or out of the air in your home. If you’ve chosen a Ducane™ coil, you’ve made a smart choice. Low Water Retention RatesThis is a list of common HVAC components in commercial buildings. You probably know that you have an HVAC system for your facility, but you might not know what all of the components do.

Here is a list of the most common HVAC elements found in a commercial building and how they work together to keep your building at its ideal temperature. An air conditioner is designed to dehumidify and remove heat from an area. The cooling is done using a simple refrigeration cycle. A condenser is a component of the basic refrigeration cycle that removes heat from the system. The condenser is the hot side of an air conditioner. Condensers are heat exchangers that can transfer heat to air or heat to fluid (such as water or glycol) to carry the heat away. An air handler, or air handling unit (often called an AHU), is used to condition and circulate air as part of an HVAC system. An air handler usually contains a blower, heating or cooling elements, filter racks or chambers, sound attenuators, and dampers. Air handlers usually connect to ductwork that distribute the conditioned air through the building and return it to the AHU. Small air handlers are called terminal units, and may only include an air filter, coil, and blower.

These smaller units are also called blower coils or fan coil units. A larger air handler that conditions 100% outside air, and no re-circulated air, is known as a makeup air unit (MAU). An air handler designed for outdoor use, typically on roofs, is known as a rooftop unit (RTU). A chiller removes heat from a liquid through a vapor-compression or absorption refrigeration cycle. This cooled liquid flows through pipes in a building and passes through coils in air handlers, fan-coil units, or other systems, cooling and usually dehumidifying the air in the building. There are two types of chillers – air-cooled or water-cooled. Air-cooled chillers are usually outside and consist of condenser coils cooled by fan-driven air. Water-cooled chiller are usually inside a building, and heat from these chillers is carried by re-circulating water to a heat sink such as an outdoor cooling tower. Now that you know the difference between these components, do you remember when the last time was that you had them tuned up?