18,000 BTU 230-Volt Electronic Window Air Conditioner with RemoteGE window air conditioners are designed to fit traditional-style windows. It comes with GE’s EZ-mount installation 18,000 BTU, 10.7 EER, 8.1/8.8 amps EZ mount window kit 3 cooling / 3 fan speeds Fits windows 26 in. - 41 in. wide, minimum height 18-1/2 in. Remote control and one-touch lift-out filter Color Appearance Light Cool Gray 2 If it is mounted in the window does it need to be taken out in the winter? 2 Is this unit quite? The one I have now is so loud you have to turn it off to talk on the phone. 2 For the loud pinging - it appears it's from the amount of water laying in the water tray - is there anyway to drain the water from the tray has the manufacture thought about putting a plug in the bottom to drain the water? Or can the owner drill a small hole for the water to drain? 2 I have the 18.000 BTU it says it takes 230 volt I do not know the gage of wire it would

I have a line that was a 220 volt would this work for my needs How many amps does my unit draw? What size wire should I use?Here are some basic tips to help you determine what you need. Wire is sold based on several factors. The most important part that will be covered here is the gauge, sometimes refered to as AWG (American Wire Gauge). Wire guage is measured from high to low with higer numbers meaning a smaller wire size. The chart below will tell you approxiamtly what wire size is needed for the amount of power that will be running over the line. Under certain circumstances a large wire size may be needed even if your amp requirment does not seem to justify it. Go to the next larger wire size if your run is more than 100 feet, inside a conduit, or ganged with other wires where the heat dissipation may be inhibited. As with all electrical work, consult a professional with any questions about special cirucmstances. After the gauge number, there will be a number signifying the amount of service wires in the cable.

The picture above shows 2 service wires plus a ground. If this wire was 14 gauge, it would be labeled "14-2" or "14/2". (The ground wire does not count.) In the example above, if this wire was 12 gauge it would be labeled "12-3" or "12/3". This wire has 3 service wires plus a ground. The example above is 14 gauge 4 conductor stranded wire which is used for most mini split air conditioners. This is known as the control wire. how to clean window ac unitThis is the minimum gauge that should be used between the indoor and outdoor units. air conditioning units power requirementsThis is not the correct wire to connect your outdoor unit to your circuit box. efficiency of an ac unitFor the main unit, refer to the chart above. When updating an appliance or air conditioner, it is important to determine the correct current draw.

If your circuit breaker is 20 amps you cannot install a product that requires 30 amps. It is not as simple as just changing the circuit breaker. The wiring to the appliance also needs to be changed. Although, when the opposite occurs, the solution is easier. If you are going from an appliance that required 30 amps and your new appliance requires only 20 amps, the wire does not need to be changed. The circuit breaker and the outlet receptacle will need to be changed. This is becuase a thicker wire has can safely carry less power, but a thinner wire can not carry more than it is rated for. If you try to run a 30 amp appliance on a wire rated for 20 amps, the wire will get hot and can create a fire hazard. Below are examples of typical circuit breakers. The one on the left is an example of a 110 volt 15 amp breaker. The 15 on the switch indicates that it is 15 amps. The one on the right is an example of a 220 volt 20 amp breaker. Once again, the 20 on the switch indicates the amperage.

These are only examples and your breakers may be different. If you are not sure consult with your electrician before ordering. This information is only a guide. If you have questions please call us or consult with your electrician.What is the correct size wire for 60 amp service? For 60-amp electrical service, 6-gauge copper or aluminum wire is the correct size to power such devices as electric furnaces and large electric heaters. A 50-amp circuit breaker or fuse box can also be powered by 6-gauge wire. When the amperage increases, the width of the wire needs to be larger to conduct more electricity. The American Wire Gauge system features smaller gauge numbers as wire widths increase. What is the wire size for 200 amp service? Where can you find a wire gauge amp chart? What is the wire size for 200 amps? The size for 6-gauge wire is 0.162 inches or 4.11 millimeters in diameter, not including insulation around the conducting wire. Every 6-gauge decrease in wire number doubles the diameter of the wire.

For example, 6-gauge wire is twice as thick as 12-gauge wire, and 0-gauge wire is twice as thick as 6-gauge wire. Typical appliances that run on 60 amps include ovens, ranges and water heaters. For homes that run on 120-volt service, 60 amps is 7,200 watts of electricity. To determine the total amount of watts on one circuit, multiply the amperage by the volts on that particular circuit. Larger gauge wire, such as 4-gauge, runs 80 amps for larger furnaces, larger water heaters and sub-panels in circuit breakers. Smaller gauge wire, including 10-gauge, runs 30 amps for electric clothes dryers, window air conditioner units and built-in ovens. Learn more about Electrical What wire size is required for a 200amp service at a distance of 180 feet? The required copper wire size for a 200amp service of 120v/240v at 180 feet is 3/0. The choice to use aluminum conductors is often made because of a signif... How do you use a wire gauge amp chart? Use a wire gauge amp chart to determine the approximate wire size for an electrical load.