DAILY DELIVERIES SERVING:  New Jersey  •  New York  •  Connecticut  •  Pennsylvania  •  DelawareTELEPHONE: 1-800-458-7329 What is Spot Cooling? Spot cooling is cooling a person, process, or equipment in an environment that would otherwise be difficult or impossible to air condition. Spot coooling air conditioning rentals are available to meet your emergency spot cooling and air conditioning needs when your customers' regular cooling equipment fails. Emergency spot cooling rentals can provide emergency air conditioning needs while your customers' standard cooling equipment is serviced, upgraded or replaced. Spot cooling rentals can also help meet your customers' supplemental cooling needs. Luce, Schwab & Kase has a 24-hour emergency spot cooler rental fleet featuring: MovinCool – Emergency spot cooling rental units OceanAire – Emergency spot cooling rental units 24-Hour Emergency Spot Cooling Rental Service for:

Moisture Removal (Learn more) Five Varieties of Emergency Spot Cooler Rentals Available: Air-Cooled Spot Coolers (1-5 tons) [Learn more] Air-Cooled Heat Pumps (14,600 Btu/h cooling/18,600 Btu/h heating) [Learn more] Water-Cooled Spot Coolers (1-5 tons) [Learn more] Air-Cooled Heat Pumps (1-5 tons) [Learn more] Click here for detailed specifications on our entire rental fleet A wide variety of accessories are available for our MovinCool line of emergency spot cooler rentals: Emergency spot cooling portable air conditioning rental systems can be used in a wide variety of air conditioning appplications including: 245 Lackland Drive West 110 Gaither Drive–Unit D Mt. Laurel, NJ 08054Some people believe that AC ducts are destined to become moldy. While all AC ducts will likely grow some mold and will become discolored with visible mold or visible dust to some degree, it is not normal or healthy for ducts to become excessively moldy, or to produce a strong mold odor.

Mold spores from AC ducts result in health problems and even mold odors in the absence of spores have been shown to cause health problems. Keeping ducts free of excessive mold is important. The information in this blog is intended to provide readers with information on:ac units for sale online 1) Some reasons why AC ducts become moldy.cost of moving ac unit 2) The importance of proper sizing of AC units.buy ac unit online 3) In addition it draws attention to a very common indoor air quality problem called entrainment. Entrainment is when AC units pull contaminated air from inside attics or walls or other undesirable areas. The following information is taken from a Broward County mold inspection we conducted on 11-17-07 it shows an actual example of how ducts became moldy and gives recommendations at the end.

The property inspected is a one story single family Broward county house built in 1974. Client reported mold growing on AC vent registers. The mold started a few weeks ago. The client reported that a new larger AC unit was installed about 3 months prior to the mold starting. This inspection is for mold conditions at the AC registers only. In the above referenced area the inspector observed a new air conditioner. The serial number on the unit indicates that it is a 4 ton unit, thus is it rated to cool a 2400 sf house. This AC unit is just a little large for this house. The inspector also observed a new condenser / compressor unit. The serial number indicates that it is a 3.5 ton unit thus designed to cool a 2100 sf house. This is also slightly large for the house. You have a newer larger AC unit. The size of this newer AC unit is a major reason for why you have humidity related cladosporium on your AC registers that were previously not moldy. The previous AC unit in use about 3 months ago was smaller than this AC system thus would have been more efficient at drying the houses air before cooling the houses air and shutting down.

If an AC is to large it shuts off after the air is cooled but before the air is properly dried / dehumidified. Air that is not dehumidified and has a humidity above 60%RH to 65%RH can and often does cause humidity problems in Florida homes. The above photo is of cladosporium mold growing in your registers. Another reason why you have mold problems now is because of the two holes in your AC return. These holes in the wall studs allow the AC to pull humidity into the AC each time the AC turns on, this phenomenon is called entrainment and is a common cause of mold and humidity problems. Yes all metal studs have these holes, but it is not typical for these open holes in the studs to be exposed and in such close proximity to an AC return. Where does the humidity in your walls come from? it comes room the attic, the attic in turn gets the humidity from outside via the soffit vents like the one in the above photo. Why did this problem not occur till recently? the older smaller AC was more efficient at drying air as stated above and thus was able to handle the humidity load created by these openings.

More photos of mold on and around your AC registers. Note that the tiny black spots on and around AC registers are very typical examples of cladosporium spheasperium, or cladosporium cladosporidies mold. This mold problem is caused by elevated humidity in your ducts. This is not likely to cause a toxic reaction, but this mold may result in allergic reactions or act as an asthma trigger in sensitive persons. The real concern is if it is growing excessively deep in your ducts then you will have much more mold than you can see on the registers. Mold growth in the ducts can and often causes health complaints. Excessive mold was not observed in your AC unit but you are recommended to have your ducts cleaned in accordance with NADCA standards or replaced.Note that the tiny black spots on and around AC registers are very typical examples of cladosporium spheasperium, or cladosporium cladosporidies mold. Based on this inspectors observations and conclusions your inspector recommends using good quality foil mastic tape or other methods to seal two openings in your AC return wall studs.