Whether you're building a new home and need a heating system installed or you have to replace a dead furnace, the installation of new heating equipment will be a costly proposition. A home's heating and air conditioning system is the costliest mechanical system or appliance within the home. Some diligent research and working with an experienced contractor can help you get the most value on a new system. Install a Furnace Costs Most homeowners spent between:$2,883To$4,428 The Average Cost to Install A Furnace The average cost to put in a furnace is $3,835. Most homeowners report paying between $3,250 and $4,420 for the installation of a new furnace. The lowest price that a homeowner might pay is $1,500, while the maximum price a homeowner has reported paying for a furnace installation was $6,990. The actual cost that you can expect to pay for a furnace installation will depend on the size and type of the furnace as well as its energy efficiency and other features. Furnaces can operate using propane, natural gas or electricity as the power source.

Oil furnaces, geothermal furnaces and solar-powered furnaces are alternative options that a homeowner might consider. The U.S. Department of Energy offers Energy Star ratings to highly efficient furnaces. To determine a furnace's efficiency, look up its AFUE, or Annual Fuel Utilization Efficiency, rating. The higher the AFUE value, the more efficient the furnace.air conditioner unit size calculator Considerations When Installing a New Furnaceair conditioning units through wall Size is one consideration when installing a furnace. best 3 ton ac unitElectric furnaces are smaller but often less efficient than other types of furnaces. Gas furnaces require the availability of natural gas and require regular maintenance to ensure that no gas or carbon monoxide is leaking.

The furnace must be properly sized to the home, as a furnace with excess capacity will use extra power while an undersized furnace will not effectively heat the home. Some homeowners add accessories such as a humidifier and air purifier, which further increase the project cost. Regular furnace repair or maintenance can bolster its efficiency and lifespan. During the winter, change the furnace filter every month. Before the winter, schedule an annual tune-up with a licensed heating service company. Last updated on May 17, 2016 Top Articles on Install a FurnaceJeff Wilson replaced his HVAC system for the same reason most homeowners do: It broke. Five years ago in the heat of summer, his air conditioner died — and this was well before he embarked on an all-out Deep Energy Retrofit (DER) to green his 70-year-old Cape Cod. Still, he used this opportunity to upgrade the old, standard unit. "We had to keep a little air conditioning on so we didn't have so much mold," Jeff says, describing a major pitfall of the home: high humidity that produced damaging condensation, causing woodwork deterioration and poor air quality.

Jeff got three bids for the HVAC project, ranging from $3,500 to trade the old HVAC unit for a comparable model to $12,000 for a state-of-the-art system. (These price estimates are from the time of installation in 2005.) "We expected gas prices to go through the roof, which they did in 2008," Jeff says, weighing the options. "And we expected this new HVAC unit to last." The 26-year-old unit Jeff replaced was 80 percent efficient — not bad for 1979 technology. But we've come a long way since then. The standard option Jeff considered as a replacement would basically restore the system to status quo for $3,500. But Jeff was looking for more. The midrange unit was priced at $4,200 and would boost the furnace efficiency to 90 percent, with a 16-SEER air conditioner. The lower the Seasonal Energy Efficiency Rating (SEER), the more energy it takes to cool the home. The high-end system would cost Jeff $5,800, but for that $2,300 more, he got more features and optimum, 97 percent efficiency.

Because the Wilsons mainly used their air conditioning to defuse the thick humidity typical in southeast Ohio during summer, a variable-speed blower was worth the investment. This mechanism allows Jeff to set the humidity level on his thermostat. "Instead of cooling your house down to get humidity levels low, you can do a bit of dehumidifying [with the blower] to keep the temperatures lower," he explains. Jeff could get this feature plus 7 percent more efficiency on the gas furnace. "We were looking toward the future," he says of the price tag and, when comparing systems, the estimated five-year payback. The choice was relatively easy for Jeff. He chose the highest-end unit and sized the HVAC system exactly to fit his home so no energy would be wasted. However, he did not figure in extra capacity to supply heat and air to the new home addition, which would come to fruition five years later. Because this addition is built using the latest green technology in new construction — and solar panel energy — he doesn't expect to need the extra power for this part of the house.

Immediately after installing the new HVAC, Jeff noticed energy bills that were about 20 percent lower. "That's pretty significant," he remarks, noting that as HVAC systems age they become less efficient. The old system was probably running at 50 percent efficiency by the time it was replaced in 2005. Invest in the best. "This is a long-term decision; it's not an appliance like a microwave," Jeff says. "By buying the highest efficiency rating possible now, you hedge your bets against the high energy prices that will come later."It may sound like a good thing if an HVAC unit kicks on and cools down a house in five minutes. "If you put in a unit that's too big, you'll fry the compressor," Jeff says. Ask the HVAC professional to size the system just right for your home.Jeff asked three contractors for estimates and made an educated decision based on the cost benefits of each. Shop around before you settle on a system or a contractor. What should I pay for a new furnace and air conditioner installed in a 1100 square foot two story townhome in NJ?

what should you pay. You pay what you can afford. 1100sqft unit requires a min. of a two ton unit. prices range from 2100-2900 depending upon the seers of the system. 13 seer is the min. the law requires and for your situation with 1100 sqft. do not worry about the seers as long as it is to code. the bigger the house the more seers for economy. 1100 sqft is at the border line for a two ton system. It is more important to have your new system balance, there is where you get the economy on your electric bill and gas. Bryant, lenox, ruud and carrier are the brands you should stay with.All have the same basic factory warrantee and will last you longer than you expect as long as you maintain it with regular check ups twice a year once in the spring and then in the fall.raymond gonzalezkoolray heating and air clarksville,tn Answered 4 years ago There are many questions to answer before anyone can give you a price for your new system. It's like calling a dealership and asking how much a new car is.

They need more details, too.Call a few HVAC contractors in your area and ask for bids to replace your system. Ask them what they recommend and why. Then compare apples to apples. A higher efficiency system will cost you more up front but will save you more on your energy bill. However, be warned that some of the super high efficiency systems don't typically pay off in savings due to their higher parts and service costs down the road.Be leary of contractors who quote you prices over the phone or internet without looking at your home. They may be either inexperienced or will hit you with higher costs once on site due to things they didn't plan for and easily could have if they had just looked at the job in advance. Many of the big box stores do this with their installation services for all kinds of things.Todd ShellTodd's Home Services by Todd's Home Services No one can tell you what another contractor will charge.There is no one set price for heating and air-conditioning equipmentinstallation.

One of the major factors that affect your price is its size. Noone can tell you what size equipment you’ll need without doing a load analysison the home. That calculation essentially determines the insulation value ofthe home, i.e... What is the heat gain of the home, what are some otherprevailing factors like room equipment, solar gain, or natural shading? You can compare prices betweencontractors to gauge what your cost would be between contractors, but this is alittle tricky to do. Let me explain a little more. Let's say you get aninstallation quote of $5050.00 from contractor “A” who employs threetechnicians and operates two trucks. He also runs his operation from home.Contractor “B” charges $6200.00 to do the same job but has 10 employees and 5trucks. He works out of a rental unit and offers his people a little bit betterof a benefit package to recruit highly motivated workers. Everything else beingequal (equipment size, SEER rating, furnace efficiency, brand name andadditional material—other things that affect the price), is either one of thesecontractors defrauding you?

No, their overhead is different. All these thingsplay into a company’s labor rate. Just be aware of your expectations when itcomes to performing any kind work in your home. If you want to pay an extremelylow-inexpensive price below the average installation cost in your area then youare highly likely to get the quality of work that comes with that cost.Remember cheaper is not better! Hopefully you got things sorted out for your new hvac system by now. Please be aware that you can save significant money by investing a small amount in air sealing all penetrations between your attic and heated space. Just use some fire-rated foam - about $7 a can and fire-rated caulk (blue) - also about $7. Stop the air from just going up and you'll save quite a bit. Make sure your attic hatch is also well sealed with foam/rubber around all edges and seals well. You may also benefit from more insulation in the attic. Most developers sub this stuff out and the job that is done is often haphazard. A nice thick layer of insulation added on top will probably only cost you about $500 and pay itself back in 2-3 years, combined with the air sealing.