Air Handling Unit Kit 10-25 kW for PACi 1. Remote control CZ-RTC42. New plastic IP 65 Box3. PAW-T10 PCB for dry contact4. 0-10V demand control PCB5. Intelligent thermostat for:Cold draft preventionOutdoor temperature shift compensation6. Terminal base for sensors and power supply The new Air Handling Unit Kit has been developed to better meet customer demand:IP 65 Box in order to be installed outside0-10V demand control (included on the CZ-CABP2 PCB)*Easy control by BMS* Only available with Elite PACi, up to from 6kW to 14kW. CZ-RTC4 Timer remote controllerOperation-ON/OFFMode selectTemperature setting* Fan operation signal can be taken from the PCB.CZ-T10 terminal Input signal= Operation ON/OFFRemote controller prohibitionOutput signal= Operating-ON statusAlarm output (by DC12 V)PAW-OCT, DC12 V outlet. OPTION terminalOutput signal= Cooling / Heating/Fan statusDefrostThermostat-ON PAW-T10, PCB to connect to T10 connectorA Dry contact PCB has been developed to easily control the unitInput signal operation ON/OFFRemote control prohibitionOutput signal operation ON status maximum 230 V 5 A (NO/NC)Output signal alarm status maximum 230 V 5 A (NO/NC)Additional available contacts:- External humidifier control (ON/OFF) 230 VAC 3 A- External fan control (ON/OFF) 12V DC- External filter status signal potential free- External float switch signal potential free- External leakage detection

OFF contact potential free (possible usage for external blow out temperature control)Hyperion 906 Power Supplyused air conditioner window units for sale The Hyperion 906 provides AC power for any Meech AC Ioniser. how much to replace inside and outside ac unitPowered by 24V DC, it produces an adjustable output of up to 7kV AC. Being 24V DC powered it is universal and easy to integrate into modern machinery.ac unit is smoking The drive electronics are efficient and allow the 906 to be lighter and smaller than traditional AC power supplies. Up to four ionisers can be connected to a single unit. Universal supply voltage, found on modern machinery, Hyperion 906 can operate independently of local mains voltage and frequency.

Output voltage of between 4 and 7kV can be set (with BarMaster programmer). This means the Hyperion 906 can be set up to suit any Meech ioniser, making it truly universal. Universal Meech HT Connection Up to four standard Meech AC products can be connected to a single power unit, without any modification. Easy to see LED indicators ensure the state of the power unit can be viewed at any angle. The colour and state of the LEDs, show whether the system is operating correctly or if it needs attention. Local and remote alert of damage or HT failure. 92mm x 110mm x 118mm 24V DC - N.B. Supply must be grounded. Adjustable, 4 to 7kV AC Murr 4 pin M8, Earth terminal 24V, Output Resistance 10kΩOJ Air2 - Control system for AHUs At OJ Electronics, we have spent four decades providing and perfecting control for air handling units (AHUs). So we know that different settings require different things. With OJ Air2, you can get it all. Pick what you want

The OJ Electronics range is about choice, too. If you want the full benefit of sophisticated control and simple handling, you can install the complete range in your system. But you can also scale your system to match project specifications, picking out specific products and control features to give your clients exactly the level of functionality and control they need. Available in 11 models. Air flow rate of 1,000 to 66,000 m3/h Air handling unit designed to meet the various mixing, filtration, heating, cooling, dehumidification, humidification, ventilation, recovery and sound attenuation needs in commercial, industrial and healthcare applications. Available as a horizontal unit for indoor installation or outdoor installation with canopy and protective accessories. Every model in the range may be ordered as single or dual path. Double-skin casing with 50 mm long fibre mineral wool insulation reinforced with bonded glass fibre cloth, peripheral frame or stainless steel support legs, depending on size, two-tone galvanised steel twin-wall panels, smooth internal walls without protruding screws as required by EN 13053

At least one removable panel per functional section as required by EN 13053, standard access panel on functional sections requiring maintenance Filter efficiency: G4, F6 to F9, H10 to H14 or activated carbon. Filter mounted on compressible runners. Stainless steel universal or large-media frame with pressure tappings on each filtration stage. Filter class F9 in accordance with EN 13053 Lift-off doors on offset hinges, twist-lock latches made of composite materials, polyamide handles, large square inspection window as required by EN 13053 Sloped stainless steel condensate drain pan as required by EN 13053 Hot water or cold water coils with standard threaded connections (up to 3") and airtight sealing flanges, thermal break between casing and tubes, electric heater Motor mounted on self-guided bracket, with belt idler, three types of fan (LP, MP and plug), mounted on anti-vibration frame, flexible internal connection sleeve between fan and casing Fitted with cable gland for electrical power supply

Adiabatic or steam humidifier Damper, single air intake, two-way mixing, three-way economiser, opposing blades, leakage class of dampers ensured by gaskets at the ends of the louvres and a continuous gasket along the side Heat recovery unit with exchange coils, plates, heat pipe or wheel, sound attenuator The AIRTECH range meets the requirements for European standards EN 1886 and EN 13053 and is manufactured in CIAT's ISO 9001 certified facilities. Designed in accordance with EN 13053 and EN 1886: T2 thermal transmittance, TB2 thermal bridging, 2A mechanical strength, B casing leakage, F9 filter bypass leakage. Meets the fan mechanical safety requirement. Manufactured in ISO 9001 certified facilities. Screws do not protrude from internal walls Complete range with a wide spectrum of flow rates and several options Double-skin galvanised steel panels, two-tone coating, class B air leakage, with optional polyurethane or epoxy coating on the outside and inside