TIL Feedback - we welcome your suggestions at til@va.gov VA Standard Details were updated in early 2009, and Div 22 and Div 26 in early 2014.  The numbering system relates to specification MasterFormat 2004.  Each detail is available in PDF and AutoCAD (DWG) formats, go to our FTP site for the DWG format drawings. Since the details are inherently graphical in nature, they are not readable by a screen reader. The links toward the top of the page are navigational, and allow the user to jump to the desired section in the formatting table below that contains the details. The columns in the formatting table indicate the detail number, the title of the detail, and provide the link to the file indicating the file type extension. Division 0 - Special Sections Division 1 - General Requirements Division 5 - Metals Division 6 - Wood, Plastics, and Composites Division 7 - Thermal and Moisture Protection Division 8 - Openings Division 10 - Specialities

Division 11 - (Hospital) Equipment Division 12 - Furnishingswindow ac unit collecting water Division 13 - Special Constructionhow much is a new 5 ton ac unit Division 14 - Conveying Equipmentwall ac heat units Division 22 - Plumbing Division 23 - HVAC and Steam Division 26 - Electrical Division 27 - Communications Division 28 - Electronic Safety And Security Division 32 - Exterior Improvements Division 33 - Utilities VA Plaques and SealsDeferring HVAC maintenance doesn’t just impair efficiency – it can also lead to breakdowns that eventually necessitate a premature and highly expensive replacement. When your staff is constantly swamped with service calls, it’s hard to find the time for basic inspections and treatments.

Unfortunately, this seemingly time- and money-saving move costs much more in the long run. The Sources of HVAC Issues Return air ductwork (if you have it) and the air handling unit are likely to attract grime first, notes Matt Mongiello, president of the National Air Duct Cleaners Association (NADCA). Coils attract biofilm, a stubborn mix of microorganisms. Areas you often don’t have time to inspect can also spread contaminants, adds Mike White, chair of NADCA’s education committee. “The air handling unit should be filtered, but depending on the type of filter you use and the frequency with which you’re changing that filter, there can be a lot of accumulation,” Mongiello explains. Cool, moist places with dirt and dust accumulation, such as VAV boxes, present the optimal breeding ground for microbial growth. Left unchecked, that buildup can eventually spread to the ductwork, White adds. If your staff is forced to constantly scramble in order to keep buildings running, it may be best to spring for a professional inspection.

“Some facilities managers are under the notion that their supply ductwork never gets dirty because they’ve always had filters and a good program, but that’s not always the case,” Mongiello explains. “Sometimes people are surprised at the amount of dirt in their supply ductwork.” Diagnose and Treat Issues If you spot buildup, don’t start with the heavy artillery. In many cases, source cleaning is sufficient, White says. For example, there are no antimicrobial disinfectants or sanitizers (the strongest categories of HVAC cleaning chemicals) with EPA approval for use in ductwork due to health concerns, so trying gentler methods first is the best way to start. “If you find contamination, the first step is source removal,” White explains. “If you have some internally lined insulation that’s coming apart and becoming airborne, go in and clean that and then put a coating on it to refurbish the material.” A HEPA vacuum and brush are often all that’s needed for ducts, White adds.

For large installations, consider hiring a cleaner to walk through and contact-vacuum contaminated areas. When in doubt, call in a professional, Mongiello recommends – an improper cleaning could contaminate clean areas. “Brushing removes the adhered particles from the sides of the ductwork,” White says. “When you put the system under negative pressure and air-sweep the inside, it brings everything back to the HEPA vacuum.” Ultraviolet disinfection lighting is gaining popularity, Mongiello notes, but its value depends on how you use it, what it’s used for, and whether it passes your cost-benefit analysis. The specialty lighting minimizes microbial growth in places like coils, plenums, and exterior HVAC applications, but bulbs can be costly to install and change, Mongiello says. Coils especially benefit from chemical cleaning, particularly when you need to dissolve already accumulated enzymes. Like any cleaning solution, check to ensure you’re using something that’s EPA-registered for this use.

Acid-based compounds like phosphoric and hydrofluoric acid solutions are most often used on condenser coils due to the type of soiling associated with their outdoor location, according to NADCA’s guide to HVAC cleaning chemicals. Alkaline cleaners, which contain chemicals like sodium hydroxide, are best to combat greasy soils. Coils often require chemical assistance because biofilm and greasy soils are very difficult to remove and their aluminum fins are easily damaged, the guide notes. After the Deep Clean Once you’ve removed accumulated debris, examine your inspection and cleaning schedule. Despite the all-too-common FM time shortage, don’t defer this maintenance step – the longer you let grime build up, the more you risk an early breakdown. A proper self-inspection starts with merely looking at the system yourself, Mongiello says. For instance, when it’s time to change the filters in the air handling unit, peer inside with a flashlight and assess the condition.