I have one Hitachi i-clean split AC 2ton unit installed in my home. I want to connect another indoor ductless unit to the already installed outdoor compressor. I only need to use one indoor unit at a time. How do I connect two indoor units to a single compressor - is this possible? If his house is relatively new and well insulated and not too enormous (1500 SF or less) and not in a very hot area, two tons is probably enough for the whole house most of the time. I've got 2.25 tons downstairs and 2.5 tons upstairs in a 3200 SF house and it's always been more than enough so 2 tons for 1500 SF or less is probably fine even if you run both evaporators at once. However, I would want to be sure that you could switch off one of the two evaporators because that seems essential to his planned usage. It could be for energy savings or just because he already knows 2 tons isn't enough for the entire house, he doesn't say. The actual question of connecting two evaporators to one condensor is quite easy, you just need to add a T to the freon supply and a T to the freon return.

But how will the compressor be told to turn on? You don't want the room with the evaporator you are not using to run the compressor. And how do you stop freon from going to the evaporator you are not using? The outdoor unit needs to have a control board that allows for more than on indoor unit to hook to. At minimal you would need to changed the board unless it already has it in it, which is not common. Then the system must have separate valves for each indoor unit so to prevent refrigerant flowing to the unit not being used.If you really do use only 1 at a time, this piping (tee it in where possible) will work. Only 1 terminal will work at a time and the condenser will only see 1 indoor coil (the load). If you use more than 1 terminal at a time, then it depends if the outdoor unit (outdoor compressor) can meet the demand (indoor coils). A 2-ton outdoor unit will give you a little more than 2-tons when more than 1 terminal unit is operating but there is a limit. Each manufacturer can be different regarding how to wire in the additional thermostat.

Check with a rep to find out the exact Tstat wiring (i.e., the inclusion of another indoor unit) and Tstat programming. It can but you must modify the circuit to protect from operating both of them at same time by the following: You need to install two T connections at the IN/OUT of compressor. Modify the compressor protection by adding relive valve to bypass the pressure upon increasing pressure. Use two solenoid valves each one at the O/P T tube which will feed the Indoor unit. Solenoid valves will be feed power from O/P terminal in indoor unite which assigned to feed out door unit and add relay protection to prevent both solenoid open. Remember if you are feeding the the two indoor unit from different power source so you must install relay or contractor which will feed the Compressor from independent power source or direct.Our Multi Zone Indoor Units offers a variety of indoor units for multiple rooms in your home. We provide a wide range of options to suit your home functionality and decor.

High Static Ducted Multi Fwhere is the copper in an ac unit High Static Ducted indoor units in 24,000 and 36,000 Btu/h capacities for use specifically with Multi F and Multi F MAX outdoor units.central air conditioning units cost to replace unit Vertical-Horizontal Air Handling Unit Multi Fcleaning an outside air conditioning unit Air handlers with convertible vertical upflow or horizontal left air distribution. Art Cool Mirror Multi F Wall-mounted indoor units with a mirror-finished front panel. Choose from 9,000, 12,000, and 18,000 Btu/h capacities. Wall-mounted indoor units with a white exterior. Available in 7,000, 9,000, 12,000, 14,300, 18,000, and 24,000 Btu/h capacities.

Art Cool Gallery Multi F Available in 9,000 and 12,000 Btu/h, the slim, contemporary styling of the Art Cool™ Gallery models will appeal to today’s discerning customer. Ceiling Cassette Multi F Four-way ceiling-cassette indoor units offered in 7,000, 9,000, 12,000, and 18,000 Btu/h capacities. Low-Static Ducted Multi F Ducted indoor units in 9,000, 12,000, and 18,000 Btu/h capacities. The HV4 series is compatible with our compatible with single zone systems. Find a Repair Provider Multi Split Air Conditioning MULTI F Outdoor Air Conditioner (5.3 kW Cooling, 6.3 kW Heating) MULTI F Outdoor Air Conditioner (7.0 kW Cooling, 8.4 kW Heating) MULTI F Outdoor Air Conditioner (8.8 kW Cooling, 10.1 kW Heating) MULTI FDX Outdoor Air Conditioner (11.7 kW Cooling, 13.5 kW Heating) MULTI FDX Outdoor Air Conditioner (14.1 kW Cooling, 18.9 kW Heating) Twin Multi-split Indoor Air Conditioners (2.6 kW Cooling, 2.9 kW Heating) Twin Multi-split Indoor Air Conditioners (3.5 kW Cooling, 3.9 kW Heating)

Multi-split Low-static Air Conditioner (2.6 kW Cooling, 2.9 kW Heating) Multi-split Low-static Air Conditioner (3.5 kW Cooling, 3.8 kW Heating) Multi-split High-static Air Conditioner (5.3 kW Cooling, 5.8 kW Heating) Multi-split High-static Air Conditioner (7.0 kW Cooling, 7.7 kW Heating) Multi-split Air Conditioner with Mirror Finish (2.1 kW Cooling, 2.3 kW Heating) Multi-split Air Conditioner with Mirror Finish (2.6 kW Cooling, 2.9 kW Heating) Multi-split Air Conditioner with Mirror Finish (3.5 kW Cooling, 3.8 kW Heating) > Multi Split Systems (Air Conditioner) Control several indoor units with one outdoor unit. Build the optimum system you desire. If you want to keep a large floor as well as many rooms comfortable, we recommend you use Multi Split to build a simple system using one outdoor unit.Choose from a large lineup of indoor units that best matches your rooms.You can mix and match them at will.Build the system that is just right for you.